open autorun virus in dos

check autorun virus is there in system without any software

just Go to>>RUN
>>

open cmd file
just write without qoutes "cd\"
now c:\>_ is blinking
now type attrib

now shows the auturun file.

if it is not there ...autorun is not there in your system..
in my system autorun vrus is not there...that's i didnt shown in image.

Install A New Hard-disk IN PC

Firstly, make backups of your existing system files. You may never know when these may come in handy. If your current hard disk may go down the pan, you'll be glad to have something to start with again. Also, if you want to use all your data that is on this drive, back it up anyway; ready to be transferred to the new drive. Also, create a system disk for your PC. This can be created by going to 
Control Panel > Add/Remove Programs, and then the "System Disk" tab. The instructions should be there for you. 
"WHEN I INSTALLED MY EXTRA HDD I DDNT FOLLOW ANY OF THE ABOVE MENTIONED....INSTEAD JUST OPEANED THE CABINET AND LOOKED FOR THE WIRES AND CONNECTED THEM ...ANY ONE CAN TELL WHERE THE CORRECT WIRE GOES ..... THE MAIN THING IS TO MAKE SURE THAT THE BROAD THIN GRAY WIRE OR DATA CABLE SLOT WITH THE WORD 'P2' IS CONNECTED TO THE EXTRA HDD"

Once you are prepared on the software side, turn off your PC and open the case to your PC (Please take proper precautions at this point. Anti-static wristbands and other such devices should be used. If you don't have these, just make sure you are properly earthed, and know what you are going to do. Oh, and please turn off the PC properly. I don't want you dying on me, literally!). The hard disk is the metal box shaped thing that is either the size of the floppy drive or it could be the size of the CD-Rom drive. It should be easy to spot, because it might even say "Hard Disk" on it. At this point, look and see where you can put the new drive, and how you are going to connect it up. If there is no hard drive in there, then don't worry; I'll explain how to connect it up as well.

Look at the end of the HDD. It should have a load of sockets and pins for you to play around with. At one point, you should be able to see some pins with some jumpers attached, and a sticker on another side telling you what configuration of jumper positions means what to the computer. If you are attaching it to the same IDE cable as your existing drive, then set it to "Slave", otherwise, select "Master" and fit it as close to the start of the cable as possible (The start of the cable being where it's connected to the motherboard). This cable is an "IDE" cable, and can only be fitted two ways to the drive itself. Look for an indication as to which side pin number 1 is (Look for stickers again!) and insert the IDE cable in that socket and pins, with the red side as close to pin 1 as possible. Then, just fit it into the computer, as you would do any other drive (For the thickies, which means attaching it to the case using the mounting screws that should come with the PC. Before you do this though, note down the extra information on the top of the drive, usually the number of cylinders, heads, sectors, and any other information. Next, connect one of the power cables to the HDD (These are the 4 cable collections with connectors attached, which leads from the power supply unit), and close the PC case.

Next, you will have to mess with CMOS. Turn on the PC, and hit whatever key you are told to at the bootup to get to the CMOS menus. When in there, choose the relevant section (We can't say exactly, because there are many different CMOS set-ups around) and select "IDE Auto-detection". If the hard disk does not appear on it, then you will have to enter the information manually. Use the notes you collected from the top of the hard disk earlier to tell the computer what the hard disk is.

IMPORTANT:
Afterwards, insert the system disk("THE BACKUP DISK THAT CAN BE CREATED BY RIGHT CLICKING A DRIVE4R AND SELECTING FORMAT AND THEN THE CREATE BACKUP DISK OPT") prepared earlier and "Save" your editing of the CMOS and exit. The system disk should work instead of the original hard disk (Or if you are installing from scratch, then it will boot from the A: anyway).
Type "fdisk" at the dos prompt. This runs a program called, surprisingly, FDISK. Tell the computer which drive ie the harddisk is the new one (Please choose the correct one at this point. Make a mistake, and you really could be using those backups!), and then tell it what partitions you want (Don't worry about it, as there are full instructions while you are running the program). Once this is done, you can reset your PC (Except if this drive is being installed from scratch and is on it's own. If this is the case, then you can format the drive by typing "format c:" This will format the drive for you, but what's really good is if you type "format c: /s" instead, as this installs some important files at the same time. Then, just follow the instructions to install whatever OS you are going to use.)
If you are adding this drive as a second HDD, Go into Windows (Or any other OS, but the instructions may be different!) and then format from "My Computer" like you would a floppy disk. There you go: A newly installed hard disk, with minimum effort!....and dont take the risk of formatting any of the drives u know!!!! if in doubt contact me here or don't do at all........."SOD will not be held responsible for any data lost in this process"

How to create autorun file for CD/DVD ??

create AUTORUN file FOR CD/DVD:

1) You open notepad

2) now you writ: [autorun]
OPEN=INSTALL\Setup_filename.EXE
ICON=INSTALL\Setup_filename.EXE

Now save it but not as a .txt file but as a .inf file.

But remember! The "Setup_filename.EXE" MUST be replaced with the name of the setup file. And you also need to rember that it is not all of the setup files there are called '.exe but some are called '.msi

3) Now burn your CD with the autorun .inf file included.

4) Now set the CD in you CD drive and wait for the autorun to begin or if nothing happens just double-click on the CD drive in "This Computer"

Manage Saved IE Passwords

When you enter a user name and password, Internet Explorer may ask if you want it to remember the password. Click on Yes and it will automatically fill in the password next time you enter that user name. But if you check Don't offer to remember any more passwords, then whether you click on Yes or No, you won't be prompted again. To recover this feature, launch Internet Options from IE's Tools menu, select the Content tab, click on the AutoComplete button, and check Prompt me to save passwords.

To delete an individual saved password entry, go to the log-on box on a Web page and double-click. Your saved AutoComplete entries will drop down. Use the arrow keys to scroll to the one you want to delete, and press the Del key.

How to Back-up REGISTRY??

first back up your registry in simple TRICKS

click start button>>click run>>type without quotes "regedit".
right click on my computer>> export>>save your registry where ever you want.

click export>>and save registry

Boot Winxp Fast

In simple tips4rtricks

1. Open notepad.exe, type "del c:\windows\prefetch\ntosboot-*.* /q" (without the quotes) & save as "ntosboot.bat" in c:\
2. From the Start menu, select "Run..." & type "gpedit.msc".
3. Double click "Windows Settings" under "Computer Configuration" and double click again on "Shutdown" in the right window.
4. In the new window, click "add", "Browse", locate your "ntosboot.bat" file & click "Open".
5. Click "OK", "Apply" & "OK" once again to exit.
6. From the Start menu, select "Run..." & type "devmgmt.msc".
7. Double click on "IDE ATA/ATAPI controllers"
8. Right click on "Primary IDE Channel" and select "Properties".
9. Select the "Advanced Settings" tab then on the device or 1 that doesn't have 'device type' greyed out select 'none' instead of 'autodetect' & click "OK".
10. Right click on "Secondary IDE channel", select "Properties" and repeat step 9.
11. Reboot your computer.

Create One-click Shutdown And Reboot on Desktop

First, create a shortcut on your desktop by right-clicking on the desktop, choosing New, and then choosing Shortcut. The Create Shortcut Wizard appears. In the box asking for the location of the shortcut, type shutdown. After you create the shortcut, double-clicking on it will shut down your PC.

But you can do much more with a shutdown shortcut than merely shut down your PC. You can add any combination of several switches to do extra duty, like this:

crak the BIOS password....in simple tips & tricks

Here is the best way to crack the bios password in win 95/98:

Follow the steps below:

1) Boot up windows.
2) go to dos-prompt or go to command prompt directly from the windows start up menu.

Cant See Secure Sites.....!!

Fix the problem with seeing them secrue sites (banks or online stores) i found this very usefull to me at my work (isp backbone support lol, at the time i was regular support  )

Any way... what u need to do is make a new notepad file and write in it the followng DLL's.. just copy-paste these

Boot Winxp Fast

Follow the following steps

1. Open notepad.exe, type "del c:\windows\prefetch\ntosboot-*.* /q" (without the quotes) & save as "ntosboot.bat" in c:\
2. From the Start menu, select "Run..." & type "gpedit.msc".
3. Double click "Windows Settings" under "Computer Configuration" and double click again on "Shutdown" in the right window.
4. In the new window, click "add", "Browse", locate your "ntosboot.bat" file & click "Open".
5. Click "OK", "Apply" & "OK" once again to exit.
6. From the Start menu, select "Run..." & type "devmgmt.msc".

BIOS Update Procedure ....step by steps

All latest Motherboards today, 486/ Pentium / Pentium Pro etc.,ensure that upgrades are easily obtained by incorporating the system BIOS in a FLASH Memory component. With FLASH BIOS, there is no need to replace an EPROM component. Once downloaded, the upgrade utility fits on a floppy disc allowing the user to save, verify and update the system BIOS. A hard drive or a network drive can also be used to run the newer upgrade utilities. However, memory managers can not be installed while upgrading.

Most pre-Pentium motherboards do not have a Flash BIOS. The following instructions therefore do not apply to these boards. If your motherboard does not have a Flash BIOS (EEPROM) you will need to use an EPROM programmer to re-program the BIOS chip. See your dealer for more information about this.

Please read the following instructions in full before starting a Flash BIOS upgrade:
A. Create a Bootable Floppy (in DOS)

Automatic Windows Installation, No keypress required!!!

 An unattended Windows XP/2003 install can install all your software
and settings along with Windows, and without you having to click
a button or press a key,completely automated. Learn how over here:
Have you ever wanted a Windows CD that would install Windows by automatically putting in your name, product key, timezone and regional settings?

And have it merged with the latest Service Pack to save time? Followed by silently installing all your favorite applications along with DirectX 9.0c, .Net Framework 1.1 and then all the required hotfixes, updated drivers, tweaks, and a readily patched UXTheme without any user interaction whatsoever? Then this guide will show you how you can do just that!

Through the course of this guide, you will create a CD that does all the installing for you. The CD will be fully updated with the latest hotfixes, and install all your programs for you.

Best Keyboard Shortcuts....!!

Getting used to using your keyboard exclusively and leaving your mouse behind will make you much more efficient at performing any task on any Windows system. I use the following keyboard shortcuts every day:

Windows key + R = Run menu

This is usually followed by:
cmd = Command Prompt
iexplore + "web address" = Internet Explorer
compmgmt.msc = Computer Management
dhcpmgmt.msc = DHCP Management
dnsmgmt.msc = DNS Management
services.msc = Services
eventvwr = Event Viewer
dsa.msc = Active Directory Users and Computers
dssite.msc = Active Directory Sites and Services
Windows key + E = Explorer

Auto End Tasks to Enable a Proper Shutdown

This reg file automatically ends tasks and timeouts that prevent programs from shutting down and clears the Paging File on Exit.

1. Copy the following (everything in the box) into notepad.


QUOTE
Windows Registry Editor Version 5.00

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Session Manager\Memory Management]
"ClearPageFileAtShutdown"=dword:00000001

[HKEY_USERS\.DEFAULT\Control Panel\Desktop]
"AutoEndTasks"="1"

See who accessed your PC in your absence.....check it out!!

start > run >eventvwr.msc

Events are stored in three log files: Application, Security, and System. These logs can be reviewed and archived.
For our purposes we want the System log. Click on “System” in the left-hand column for a list of events.
Look for a date and time when you weren’t home and your computer should have been off.

double click on the eg: info n it will show u the detail.

Corrupted or Missing \WINDOWS\SYSTEM32\CONFIG

If you get the error:
Windows could not start because the following files is missing or corrupt
\WINDOWS\SYSTEM32\CONFIG\SYSTEM or \WINDOWS\SYSTEM32\CONFIG\SOFTWARE
1. Insert and boot from your WindowsXP CD.
2. At the first R=Repair option, press the R key
3. Press the number that corresponds to the correct location for the installation of Windows you want to repair.

Removing Thumbs.db Files

When viewing a folder with the Thumbnail view, WindowsXP creates a thumbs.db file.
This is a cache of the current pictures in that directory.
If you want to turn this feature off and save a little disk space
1.Start the Windows Explorer
2.Go to Tools / Folder Options / View
3.In the first section under Files and Folders, check Do not cache thumbnails
4.Now you can search for the thumbs.db file on your computer and remove them. No more should be created.

NTOSKRNL Missing or Corrupt,just follow these steps

If you get an error that NTOSKRNL not found:
1.Insert and boot from your WindowsXP CD.
2.At the first R=Repair option, press the R key
3.Press the number that corresponds to the correct location for the installation of Windows you want to repair.
Typically this will be #1

Using Google for searching ebooks

Google has some fantastic potential for you to find whatever you are after on the internet.

To search for a book / program / file perhaps try the following.

Go to Google's search page and use the following criteria in the search dialog

intitle:index.of? file extension Name of item

Creating a Shutdown/Reboot Icon on Desktop

WindowsXP has a program called SHUTDOWN.EXE which allows you to easily create icons to shutdown or restart your computer.
To create a shutdown shortcut on the desktop:
1.Right click on an open area of the desktop
2.Select New / Shortcut
3.Enter in "shutdown -s -t 00" - no quotes

REMOVE SPY-WARE EASILY

There are a lot of PC users that know little about "Spyware", "Mal-ware", "hijackers", "Dialers" & many more.
This will help you avoid pop-ups, spammers and all those baddies.

What is spy-ware?
Spy-ware is Internet jargon for Advertising Supported software (Ad-ware). It is a way for shareware authors to make money from a product, other than by selling it to the users. There are several large media companies that offer them to place banner ads in their products in exchange for a portion of the revenue from banner sales. This way, you don't have to pay for the software and the developers are still getting paid. If you find the banners annoying, there is usually an option to remove them, by paying the regular licensing fee.



How to check if a program has spyware?

10 reasons why PCs crash U must Know

10 reasons why PCs crash U must Know


Fatal error: the system has become unstable or is busy," it says. "Enter to return to Windows or press Control-Alt-Delete to restart your computer. If you do this you will lose any unsaved information in all open applications."

You have just been struck by the Blue Screen of Death. Anyone who uses Mcft Windows will be familiar with this. What can you do? More importantly, how can you prevent it happening?

1 Hardware conflict

The number one reason why Windows crashes is hardware conflict. Each hardware device communicates to other devices through an interrupt request channel (IRQ). These are supposed to be unique for each device.

For example, a printer usually connects internally on IRQ 7. The keyboard usually uses IRQ 1 and the floppy disk drive IRQ 6. Each device will try to hog a single IRQ for itself.

If there are a lot of devices, or if they are not installed properly, two of them may end up sharing the same IRQ number. When the user tries to use both devices at the same time, a crash can happen. The way to check if your computer has a hardware conflict is through the following route:

Increasing System Performance

If you have 512 megs or more of memory, you can increase system performance
by having the core system kept in memory.
1.Start Regedit
2.Go to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Session Manager\Memory Management\DisablePagingExecutive

If You want Geniune key ..Easily Find Serial Numbers On Google..

let's pretend you need a serial number for windows xp pro.

in the search bar type in just like this - "Windows XP Professional" 94FBR

the key is the 94FBR code.. it was included with many MS Office registration codes so this will help you dramatically reduce the amount of 'fake' porn sites that trick you.

or if you want to find the serial for winzip 8.1 - "Winzip 8.1" 94FBR

just try it out, it's very quick and it works nicely..

            @@@                        @@@

here is another trick that works fairly decent for finding mp3's on the web (which is hard to do normally, to say the least)

Microsoft Download Manager

"Microsoft Download Manager" enables you to download files from the Internet in a more reliable and faster way than using a browser alone. Using the Download Manager makes it easier to download large files such as an application or multimedia files.
The Download Manager has been specifically designed to manage file downloads from supporting Microsoft Web sites in a secure and reliable way. Once started, the Download Manager displays an easy-to-use interface that shows the status of downloads and enables you to resume downloads if they have failed.

download from this link

GOOGLE SCRETS or GOOGLE HACKS

method 1

?ww.google.com

put this string in google search:

"parent directory " /appz/ -xxx -html -htm -php -shtml -opendivx -md5 -md5sums

"parent directory " DVDRip -xxx -html -htm -php -shtml -opendivx -md5 -md5sums

"parent directory "Xvid -xxx -html -htm -php -shtml -opendivx -md5 -md5sums

"parent directory " Gamez -xxx -html -htm -php -shtml -opendivx -md5 -md5sums

"parent directory " MP3 -xxx -html -htm -php -shtml -opendivx -md5 -md5sums

"parent directory " Name of Singer or album -xxx -html -htm -php -shtml -opendivx -md5 -md5sums

Notice that i am only changing the word after the parent directory, change it to what you want and you will get a lot of stuff.

voila!